#CLOVER EFI 2 HOW TO#
#CLOVER EFI 2 INSTALL#
#CLOVER EFI 2 FULL#

I’ve made Hackintoshes before… I have another one here running 10.9, and I got 10.9 running on this machine.

#CLOVER EFI 2 HOW TO#

I have no idea how to proceed from this point. But every time it has hung at DSMOS Has Arrived. Careully check USB stick after preparation. I’ve repeatedly tried doing this just as described, in case I missed something. ** Attempt to boot with -v npci=0x2000 kext-dev-mode=1 ** Copy SSDT from DMG to EFI/CLOVER/ACPI/patched. ** Copy kexts from DMG into EFI/CLOVER/kexts, including “10.10 Driver”.

#CLOVER EFI 2 INSTALL#

** Partition USB stick, install clover, run command to put OS installer onto USB drive.

#CLOVER EFI 2 FULL#

** Set BIOS: CSM => disabled, Secure Boot => Other OS, USB Boot => Full I have spent many hours now trying to do this exactly as you say, with no success.ĭetails again: Z97 Pro WiFi AC, i7 4790k, internal Intel graphics. I know it’s a good board because as I say I had success with 10.9. I have tried just about every combination of switches, re-checked BIOS (CSM is off, USB boot set to full, security set to Other OS).Įverything I have tried still hangs at “DSMOS has arrived”. Laptop/Lenovo Lenovo ThinkPad X1 Extreme (Gen 2) Lenovo ThinkPad X1 exit 1 fi Enable the. So I tried other switches that have sometimes been of use before: npci=0x2000, IGPEnabler=1, GraphicsEnabler=Yes (and No), PCIRootUID=0 Check out my GitHub repo for the latest Clover EFI files. Note 2: I have tried this with and without AppleIntelFramebufferAzul.kext and AppleKextExcludeList.kext.Ĥ) Copy SSDT for my board into /EFI/CLOVER/ACPI/patched.ĥ) Try to boot using -v and kext-dev-mode=1. That overwrites the generic FakeSMC kext. (Note 1: I am copying in the generic extension kexts first, then the kexts for my board. Graphics: native Intel.ģ) Copy kexts into /EFI/CLOVER/kexts on the USB EFI partition. I got this to boot with 10.9, so I’m trying to figure out what went wrong. I have tried following your guide, but trying to boot from USB I’m not getting past “DSMOS has arrived”. I have a headache just trying to describe what is going on. I’m hoping I can just do option 1, and then using SuperDuper, I can just clone my existing 10.10 installation to the “newly formatted 10.10 Fusion Drive”. I’m new to Clover but I am familiar with Hackintosh, and creating my own Fusion Drive.Ĭorrect me if I’m wrong, but I think these are my options:ġ) Break my 10.9 Fusion Drive into two separate drives again, and re-assemble an entirely new Fusion DriveĢ) Just Reformat “Macintosh HD” from my 10.9 Fusion Drive, and install 10.10 on it (though I’m not sure if Clover will conflict with Chimera’s Apple_Boot/Boot OS X’s helper partitions)Īs of right now, I have 10.10 installed in a separate SSD than the 10.9 Fusion Drive. I’ve been wanting to switch to Clover, for reasons that it seems to be newer/better than Chimera. What’s the best way to create a fresh 10.10 installation under Clover, if I want to use Fusion Drive again (not necessarily “re-using” existing 10.9 installation) I have an existing working 10.9 installation on Fusion Drive, with Chimera.

Clover efi 2